- DOWNLOAD Perkins EST 2022A ( 1 PC )
$84.00Add to cart
- DOWNLOAD Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
$51.00Add to cart
- DOWNLOAD Diamond Logic Builder DLB 2019 Database 2019
$48.00Add to cart
- Description
- Tags
- Reviews (0)
Description
Circuit Description
The aftertreatment temperature sensors are used by the electronic control module (ECM) to monitor the engine exhaust temperatures in the aftertreatment system. The aftertreatment temperature sensors are thermistors and change resistance based on the temperature being measured. The ECM provides a 5 volt reference voltage to the sensor. The ECM monitors the change in signal voltage and converts this to a temperature value.
When the exhaust temperature is low, the sensor or thermistor resistance is high. The ECM signal voltage only pulls down a small amount through the sensor to ground. Therefore, the ECM senses a high signal voltage or a low temperature. When the exhaust gas temperature is high, the sensor resistance is low. The signal voltage pulls down a large amount. Therefore, the ECM senses a low signal voltage, or a high temperature.
Component Location
The aftertreatment diesel oxidation catalyst intake temperature sensor is located in the aftertreatment system. It is located at the intake of the aftertreatment catalyst. Refer to the OEM service manual.
Conditions for Running the Diagnostics
This diagnostic runs immediately after the engine has been started.
Conditions for Setting the Fault Codes
The diesel oxidation catalyst intake temperature is less than 150?C [302?F] for 5 minutes.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or Malfunction Indicator Lamp (MIL) after the diagnostic fails on two consecutive trips.
Conditions for Clearing the Fault Code
To validate the repair, start the engine and let it idle for 5 minutes.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will turn off the MIL after three consecutive trips where the diagnostic runs and passes.
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes of this fault code include:
A malfunctioning variable geometry turbocharger (VGT)
An in-range malfunction of the aftertreatment diesel oxidation catalyst intake temperature sensor
Exhaust system leaks.
Possible Cause:
1) Turbocharger failure
2) VGT Actuator failure
3) Charge-air cooler failure
4) ECM calibration
Related
Tags: 2010-12, 31, 3495, 3711, Active, CM2250, Code, Condition, Cummins, Diesel, due, Exhaust, Exists, Fault, Filter, FMI, Gas, Inhibited, ISX15, Low, Particulate, PID, regeneration, SPN, Temperature-, to
Reviews
There are no reviews yet.
Be the first to review “Cummins ISX15 CM2250 (2010-12) Fault Code: 3495 PID: SPN: 3711 FMI: 31 Diesel Particulate Filter Active Regeneration Inhibited Due to Low Exhaust Gas Temperature- Condition Exists”
Categories Cumminz, DTC TRUCKS, ISX15 CM2250 (2010-12)Tags 2010-12, 31, 3495, 3711, Active, CM2250, Code, Condition, Cummins, Diesel, due, Exhaust, Exists, Fault, Filter, FMI, Gas, Inhibited, ISX15, Low, Particulate, PID, regeneration, SPN, Temperature-, to
- DOWNLOAD Meritor Wabco Tool Box 12.12
$40.00Add to cart
- DOWNLOAD Cat Factory Password Generator 1.0 2019 WINDOWS 10
$56.00Add to cart
$76.00Add to cart
- Related Products
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)$40.00Add to cart
cummisznn
Cumminmms Insite pro 8.9 Diagnostic Software$80.00Add to cart
Trucks software
JPRO Diagnostic Software Download 2024$100.00Add to cart
Trucks software
AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125$120.00Add to cart
Trucks software
DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC$106.00Add to cart
Trucks software
Bendix Acom Pro 2023 V1 diagnostic software 1PC$83.00Add to cart
Trucks software
VOLVOUU PTT TECH TOOL 2.8.220 2023 Last version 1pc$200.00Add to cart
Trucks software
Download Allison Doc Premium Update 2023 v2$105.00Add to cart
DEUTZ
MANUAL SERVICE DEUTZ AGROTRON 106-110-115-120-135-150-165 MK3$45.00Add to cart
DAF
SERVICE MANUALDAF xf xe engine manual$45.00Add to cart
EATON
SERVICE MANUAL EATON UltraShift PLUS$45.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 225 SMS$45.00Add to cart
Trucks software
Download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )$75.00Add to cart
CARRIE
$45.00Add to cart
DETROIT
SERVICE MANUAL DETROIT DIESEL V-71$45.00Add to cart
CAT
DOWNLOAD CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )$64.00Add to cart